Fermentation Control with Peltier Cooler? - Homebrew Talk
2006年4月19日 · Funny I just built a two carboy cabinet out of a Vinotemp peltier cooler given to me. I built a 30"x15"x28" box out of 2" foam insulation board. I put the peltier though the wall and used a wall wort to power the two 12 volt fans and the 12 volt peltier junction. I have ordered one of the aquarium temp controllers to control it.
DIY Peltier cooler - Homebrew Talk
2015年8月25日 · Brewing in Cal heat fermentation chamber is a plastic garbage can filled with water and regulated with digital thermo adding reusable ice as needed. Bought borrowed and dickered some 12v peltiers, 12v water pump, alum water cooler, 12v 30a power source, 110v controller, tubing, fittings...
Peltier fermenter cooler using water heat exchangers
2009年9月24日 · Thanks, yeah I have seen some commercial peltier water coolers, they looked a bit more industrial than for just fish tanks but were of a cold plate design, the water ran through holes drilled in the plate. the idea of using heat sinks to form a tunnel was to increase the surface area and therefore the heat transfer.
Thermoelectric (peltier) Fermentation Cabinet Build
2008年1月9日 · The thermoelectric cooler (peltier) is going to be on the top, powered by an old computer power supply. A hole will be cut in the top of the cabinet to allow the cold plate to come through. The interior and exterior heatsinks will have a computer fan on them to expedite the transfer of heat so that the cooler will work well.
Anyone use a thermoelectric (peltier) cooler/heater for fermenting ...
2013年11月17日 · I like the idea of directly heating/cooler the fermenter instead of placing the fermenter in a conditioned environment. My planned fermentation space is in my basement and never exceeds 80F. The idea of a Peltier heating/cooling setup is very appealing to me especially if I start fermenting in Sankes.
Peltier Carboy Cooler/Heater - Homebrew Talk
2010年8月23日 · I have had this idea for a while and finally got some time to build a proof of concept. It is a 6.5 gallon carboy, thin copper sheet, peltier element, heat sink, fan, and an exercise mat jacket. I used arctic silver thermal adhesive to bond the copper to the peltier and the peltier to the heat sink.
Conical Fermenter cooler/chiller (peltier) - Homebrew Talk
2011年1月3日 · The coolIT exchanger is a very nice piece of engineering very compact, colplete with pump, peltier cells, reservoir, fan and it comes with a controller board that can control the power applied to the 6 cells and the speed of fun/pump according to set point and current measured temperature.
Fermenter Cooler project - Homebrew Talk
2012年1月8日 · The advantage to using a peltier cooler is the relatively low cost to mfg a specialty device like a chilled fermentation environment, and the very small footprint of the cooling mechanism (the peltier cooler itself is only 40mm x 40mm x 3mm (1.5" x 1.5" x 1/8")). Fish
Peltier TEC Carboy Cooler - Homebrew Talk
2013年10月27日 · Currently I'm able to maintain the water temperature surrounding the carboy at 62F (75F ambient) with only the more powerful cooler running @ 4.6V through the step down converter. With the two fans running (one in the power supply, the other on the heatsink) I'm drawing 40W according to my Kill-A-Watt.
compact peltier cooled carboy setup - Homebrew Talk
2020年2月16日 · The 1.5" packing foam + mylar insulation has an R value of about 3.9 (imperial units), to be compared to about 6 for an inch of polyisocyanurate ; the insulated keg leaks or gains 1.1 W per K (or 0.6 W per ℉) temperature difference, so 22W for 20K difference, which the cooler can handle. The peltier system can remove 50W while cooling down ...